{"id":2792,"date":"2023-06-24T06:47:49","date_gmt":"2023-06-24T10:47:49","guid":{"rendered":"https:\/\/kgworks.ca\/?p=2792"},"modified":"2023-06-24T06:47:49","modified_gmt":"2023-06-24T10:47:49","slug":"trim-adhesive","status":"publish","type":"post","link":"https:\/\/kgworks.ca\/?p=2792","title":{"rendered":"Trim adhesive"},"content":{"rendered":"\n<figure class=\"wp-block-image size-full\"><a href=\"https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0946.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"640\" height=\"480\" src=\"https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0946.jpg\" alt=\"\" class=\"wp-image-2769\" srcset=\"https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0946.jpg 640w, https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0946-300x225.jpg 300w\" sizes=\"(max-width: 640px) 100vw, 640px\" \/><\/a><\/figure>\n\n\n\n<p>Using Permatex or 3M contact adhesive is a bit of a pain. The way I get a smooth thin coat on both surfaces is to use a small paint brush.  It still dries quickly. I do a small bit at a time so I can get it smooth before it starts to tack up.  When done I use reducer to clean up the brush.<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><a href=\"https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0945.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"640\" height=\"480\" src=\"https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0945.jpg\" alt=\"\" class=\"wp-image-2768\" srcset=\"https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0945.jpg 640w, https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0945-300x225.jpg 300w\" sizes=\"(max-width: 640px) 100vw, 640px\" \/><\/a><\/figure>\n\n\n\n<p>Perfect use of the adhesive is to re-glue the trim to the backing that runs down the inside of the back door opening.<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><a href=\"https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0957.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"640\" height=\"480\" src=\"https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0957.jpg\" alt=\"\" class=\"wp-image-2787\" srcset=\"https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0957.jpg 640w, https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0957-300x225.jpg 300w\" sizes=\"(max-width: 640px) 100vw, 640px\" \/><\/a><\/figure>\n\n\n\n<p>I also used it to glue down the t bar panel. There are tiny holes behind each tab where I used a pointed probe to push the tabs in place. Maybe there is a better way, but I tried others and this was the only one that worked well.<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><a href=\"https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0956.jpg\"><img loading=\"lazy\" decoding=\"async\" width=\"640\" height=\"480\" src=\"https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0956.jpg\" alt=\"\" class=\"wp-image-2786\" srcset=\"https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0956.jpg 640w, https:\/\/kgworks.ca\/wp-content\/uploads\/2023\/06\/IMG_0956-300x225.jpg 300w\" sizes=\"(max-width: 640px) 100vw, 640px\" \/><\/a><\/figure>\n\n\n\n<p>The inside of this panel&#8217;s cover had broken away from the attaching points in a couple of places.  So rather than remove the panel and try to repair the old velcro type attaching points I decided to use a couple of trim screws to cure the problem.  This is after all an <strong>amateur<\/strong> restoration.<\/p>\n","protected":false},"excerpt":{"rendered":"<p>Using Permatex or 3M contact adhesive is a bit of a pain. The way I get a smooth thin coat on both surfaces is to use a small paint brush. It still dries quickly. I do a small bit at a time so I can get it smooth before it starts to tack up. When &hellip; <\/p>\n<p class=\"link-more\"><a href=\"https:\/\/kgworks.ca\/?p=2792\" class=\"more-link\">Continue reading<span class=\"screen-reader-text\"> &#8220;Trim adhesive&#8221;<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[],"_links":{"self":[{"href":"https:\/\/kgworks.ca\/index.php?rest_route=\/wp\/v2\/posts\/2792"}],"collection":[{"href":"https:\/\/kgworks.ca\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/kgworks.ca\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/kgworks.ca\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/kgworks.ca\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=2792"}],"version-history":[{"count":2,"href":"https:\/\/kgworks.ca\/index.php?rest_route=\/wp\/v2\/posts\/2792\/revisions"}],"predecessor-version":[{"id":2799,"href":"https:\/\/kgworks.ca\/index.php?rest_route=\/wp\/v2\/posts\/2792\/revisions\/2799"}],"wp:attachment":[{"href":"https:\/\/kgworks.ca\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=2792"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/kgworks.ca\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=2792"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/kgworks.ca\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=2792"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}